Siemens thermostaat RDU50 Handleiding

PDF Handleidingen
2 Pagina's Nederlands

Siemens thermostaat RDU50
Pagina's
VAN
2
CE1B3061en / 05.02.2003 Subject to alteration Siemens Building Technologies / HVAC Products
Operating Instructions RDU…
RDU... – the temperature controller that allows you to easily set the room temperature you want. You have
2 choices. You can either rely on the factory settings or make adjustments that suit your individual needs.
Display
Settings and operation
Normal operation
Energy saving mode
Display of current
room temperature
or new setpoint
Warmer / colder
Adjustment of
temperature setpoints
3061Z01en
Heating valve open
Cooling valve open
Display of actual
room temperature
Buttons for setpoint adjustments
Heating mode, Off, cooling mode
Operating mode
selector
(RDU50.2)
Are your rooms too warm or too cold?
Normal operation
The + / - buttons allow you to increase or decrease the current room temperature setpoint in steps of 0.5 °C.
To do this, proceed as follows:
• Press
or once
The setpoint display starts flashing
• Press the buttons again to change the room temperature setpoint
10 seconds after the last press, the new temperature setpoint will automatically be stored. The display stops flashing.
Changing from heating to cooling mode
/
Automatic changeover
With the RDU50.2, manual changeover modes selector
from heating mode, Off to cooling mode.
Off = out of operation.
Display shows that the heating output is active
Display shows that the cooling output is active
Changing from normal operation to energy
saving mode
/
Changeover from normal operation to energy saving mode
takes place automatically via an external contact
(window switch / remote operation switch, etc.).
(Exception with type RDU50.2 in Off mode)
Display shows normal operation.
Display shows energy saving mode.
Energy saving mode
If you want to change the factory-set temperature
setpoints (16 °C for heating and 28 °C for cooling), follow
the procedure given below (“Changing the control
parameters”).
Important:
The setpoint of energy saving mode can be set to Off.
This means that the controller is not active in energy
saving mode and the parameter display shows Off.
Risk of frost!
Gerelateerde Handleidingen voor Siemens thermostaat RDU50
110
Siemens thermostaat 110

Voor thermostaat (2 Pagina's)
160
Siemens thermostaat 160

Voor thermostaat (2 Pagina's)
2NC9 840
Siemens thermostaat 2NC9 840

Voor thermostaat (1 Pagina's)
140
Siemens thermostaat 140

Voor thermostaat (2 Pagina's)
21-115532-001
Siemens thermostaat 21-115532-001

Voor thermostaat (28 Pagina's)
REV12
Siemens thermostaat REV12

Voor thermostaat (18 Pagina's)
REV17
Siemens thermostaat REV17

Voor thermostaat (40 Pagina's)
REV91
Siemens thermostaat REV91

Voor thermostaat (3 Pagina's)
REV13
Siemens thermostaat REV13

Voor thermostaat (2 Pagina's)
REV11 - Landis Staefa
Siemens thermostaat REV11 - Landis Staefa

Voor thermostaat (2 Pagina's)
RDD100
Siemens thermostaat RDD100

Voor thermostaat (2 Pagina's)
RDD10 - Landis Staefa
Siemens thermostaat RDD10 - Landis Staefa

Voor thermostaat (2 Pagina's)
RDF301.50
Siemens thermostaat RDF301.50

Voor thermostaat (82 Pagina's)
QAA80
Siemens thermostaat QAA80

Voor thermostaat (3 Pagina's)
REV16
Siemens thermostaat REV16

Voor thermostaat (18 Pagina's)